The PowerBook 180, like other 100 series laptops, suffers from many different issues.
ABS plastic on just about anything made in the 1990s has become very brittle with age, and this includes the PowerBook 180. The most frequent place on the 180 where you'll see this issue is with the screw mounts for the screen hinges. These mounts will break and crumble away with use, and lead to further plastic damage if the hinges are used in this state. A tell-tale sign of this issue is a gap in the plastic on the back near the hinges. If you see a gap, you've got broken standoffs. In addition, the screw mounts for the drive cages, and really just about every one in the system commonly stress crack with age.
Multiple methods can be used to prevent and fix these weak screw mounts. The one I'd recommend the most is to replace the old brittle mounts with new 3D-printed ones. These new mounts include a large plastic plate that mounts behind the LCD, in order to allow extra area for the part to be glued to, and to relieve stress from the mounts themselves. These parts when applied correctly are very strong and last a long time. A link to the STL files for the new parts is available on the resources page.
Another method of repair if you don't have access to a 3D printer is epoxy. Lots of epoxy. This method works best if the original mounts are still intact, as otherwise they can be very difficult to reassemble. The idea is that you put a bunch of plastics epoxy around all of the mounts, in order to prevent them from breaking, and to add extra rigidity to the area. This can work when done right, but I'd still recommend the 3D printing approach if possible.
The PowerBook 170 suffers from LCD Tunnel Vision, a common defect found in Active Matrix Monochrome and Grayscale LCDs manufactured by Hosiden. More info on this fault is available here.
As with any computer this old, it's more common to see a dead hard drive in one of them than one that works. Especially so, as drives used in the 180 are especially prone to failure. Apple laptops of this time used drives from one of three vendors: IBM, Conner Peripherals, and Quantum. Quantum drives are nearly always dead due to an internal rubber bumper in them that goes sticky, getting the heads stuck. Some Conner drives were also affected by this. This can sometimes be fixed with careful work inside of the drive, but it's tough.
Otherwise, these PowerBooks used SCSI 2.5" drives, which are pretty tough to find nowadays. If you do have a dead drive, I'd recommend replacing it with a modern solid state solution instead of paying silly money for spinning rust off eBay. Multiple options are available, and more info is available here.
The main battery for the 100 series PowerBooks is NiCad based, so they leak pretty frequently. Don't leave an intact one in your laptop, and make sure to check any unit you get your hands on for one. Usually the logic board only ends up damage in the event of a pretty severe leak luckily. Also, if the battery has shorted (which is pretty common), the laptop won't start with it installed. If you have a known-good AC Adapter and your PowerBook is acting dead, there's a good chance that's why.
The PRAM battery in the 180 is a rechargeable Lithium coin cell. These rarely leak. Still probably a good idea to remove it if you get the chance though, but be warned, it is soldered right to the internal interconnect board, so getting it out is a bit of a pain.
The original external PSU for these laptops uses ELNA Long-Life caps inside, which are well known to leak the worst out of just about any brand. They just love to barf their guts out all over the place in anything they're installed on and cause a real mess. They're what's behind the Mac IIsi PSU's awful reputation, and there are a couple of them inside the 100 Series PSU. So yeah, recapping them is pretty much required at this point. Getting one open is a challenge though, as you pretty much have to break it open. A vice and a couple of pencils is the best way I know to do this, and will usually get them to pop without much damage.
If you wouldn't like to bother with any of that, and I can't blame you if you don't, another option is to get an inexpensive replacement off of Amazon or eBay. The voltage and barrel jack requirements for these are so simple that replacements are still available.
Index < Macintosh Portal < PowerBook Home < PowerBook 100 Series Home < PowerBook 180 Home < PowerBook 180 Issues